Understanding Plumber's Essentials for Bathtub Installation
Understanding Plumber's Essentials for Bathtub Installation
Blog Article
The publisher is making several great points related to How to Install a Bathtub in general in the article followed below.
Installing a bath tub isn't precisely brain surgery, however it does need solid plumbing, carpentry, and also occasionally, tiling skills. Changing an old tub with a brand-new one is likewise a moderately difficult task. If the old tub is easily obtainable, the task can move immediately; if you have to open a wall to remove the old bathtub and also place the brand-new bathtub, the job is a lot harder. In either instance, the job is within a residence handyman's abilities, although you will need an assistant to leave the old bathtub as well as embeded in the new one. Ensure you have certified yourself for the work as well as are comfortable attempting it. Instead of working with a professional to take over a halfway-completed task, it is far better to think about utilizing one before you start. Chances are you might need a specialist plumber to make tube connections.
This write-up will certainly aid you set up a new tub in your restroom if you have actually currently purchased a new bathtub as well as do not need to alter the setup of your previous water pipes.
Your devices and material checklist must make up the following:
Removing Old Touches
If you need to change old faucets with brand-new ones as a part of your installation, after that the first thing you ought to do is detach the water system. After doing so, switch on the taps to drain any water continuing to be in the system. The process of eliminating the existing faucets can be quite bothersome as a result of the limited access that is usually the case.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the taps. Have a cloth all set for the staying water that will certainly come from the pipes. As soon as the supply pipelines have actually been removed, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from transforming during this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleaned up of any old securing compound.
Before going on to fit the brand-new faucets, compare the pipeline connections on the old faucets to the brand-new taps. If the old taps are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the new taps are plastic, after that you will certainly need a plastic connector to avoid damages to the string. One end of the connector fits on the plastic tail of the tap and also the various other end provides a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly require reducing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, place the faucet in the placing opening in the bath/basin ensuring that the washing machines are in place in between the faucet as well as the sink. Protect the faucet in place with the producer provided backnut. When the faucet is firmly in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with typical faucet connectors. The previous type must be linked to the faucet ends initially, tightening just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Installing the Bath tub
Using the two wood boards under its feet, place the tub in the called for position. The wooden boards are handy in uniformly spreading the weight of the bathtub over the location of the boards instead of focusing all the weight onto 4 tiny points.
The next objective is to make sure that the bathtub is leveled all round. This can be accomplished by checking the level and also changing the feet on the bath tub up until the spirit level reads degree.
To mount faucets, fit the bottom of the outermost flexible faucet port to the ideal supply pipe by making a compression sign up with; after that do the exact same for the various other faucet.
Switch on the water as well as examine all joints and new pipework for leaks as well as tighten them if necessary. Load the bathtub and also check the overflow electrical outlet and also the regular electrical outlet for leakages.
Lastly, take care of the bathroom paneling as defined in the manufacturer's user's manual. Tiling as well as sealing around the bath tub ought to wait until the bath tub has actually been used at least when as this will resolve it into its last setting.
Preparing for the Installment
First of all, the sustaining framework supplied with the bathroom ought to be fitted (if called for) according to the supplier's directions. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is necessary to make certain that if the tap includes a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the taps system to stop strain on the bathtub.
Fit the adaptable faucet adapters to the bottom of the two taps making use of 2 nuts and olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you use all of the provided washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bath must now prepare to be suited its last setting.
Tiling Around the Tub
In the location where the bathroom satisfies the tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to fracture an inflexible seal, triggering the water to penetrate the wall in between the bath and the tiling, bring about difficulties with moisture and possible leaks to the ceiling below.
You can pick from a variety of coloured sealants to assimilate your fixtures and installations. They are sold in tubes as well as cartridges, and also can securing spaces approximately a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to constantly fill the tub with water before sealing, to enable the activity experienced when the tub remains in use. The sealer can fracture relatively very early if you do not think about this movement before sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also conveniently readily available on the marketplace. It is recommended to fit the tiles using water-resistant or water resistant sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been shown that write-up on A Step-by-Step Guide to Installing a Bathtub from someone on a different website. Sharing is caring. You never know, you may be helping someone out. Many thanks for going through it.
Quick service, just dial! Report this page